Wed. Jul 6th, 2022

10.10 0.1 is the default IP address of cable routers and modems. Most notable is the default gateway address of Xfinity routers. Some other brands that use as the default router IP address for cable, broadband routers, and modems are Agere, Airlink, Arris, Aztech, Cisco, Lucent, Proxim, and Technicolor.

Also, read: 10.0.0.1 IP address

10.10 0.1 Login Admin

To access the router management interface, follow these steps:

  1. Type http://10.10 0.1 in the address bar of your browser and press “Enter”.
  2. If you typed the IP address correctly and you see an error page, your router IP address is not 10.10 0.1 Piso wifi.
  3. If you see the username and password screen, you have reached the login page of the router management interface. If you know the username and password of your device, you can log in using them.
  4. If you do not know, you can find the necessary information in the username and passwords table below. You can also find login information on the sticker at the front or bottom of the router.

Here is some popular router credential information.

Router Brand

Login IP

Username

Password

3Com http://192.168.1.1 admin admin
Belkin http://192.168.2.1 admin admin
BenQ http://192.168.1.1 admin admin
D-Link http://192.168.0.1 admin admin
Digicom http://192.168.1.254 admin Michelangelo
Digicom http://192.168.1.254 user password
Linksys http://192.168.1.1 admin admin
Netgear http://192.168.0.1 admin password
Sitecom http://192.168.0.1 sitcom admin
Thomson http://192.168.1.254 user user
US Robotics http://192.168.1.1 admin admin

Common 10.10 0.1 Problems

Can’t Connect to 10.0.0.0.1

  • If you are trying to connect to a 10.10 0.1 Piso wifi IP address, you will never ever connect as this is the wrong IP address. Correct IP address is 10.10 0.1.

Refused to Connect to Xfinity Router

  • If you are getting any such error, it means either network is down or there is no device on the local area network with IP. It is always better to connect to the router through an Ethernet cable while troubleshooting.

Comcast IP  Taking Long to Respond

  • This means either device can not reach Comcast’s default gateway or the device is malfunctioning. Make sure that the connection to the Comcast device is up and it is available on IP 10.10 0.1. Try to reboot the router and connect again after some time.

IP Address Restrictions

10.10 0.1 Piso wifi is a private IP address decided by the IETF and IANA. It is not available on a public network. It is only visible inside the private network. As this IP address is assigned to routers and modems, do not try to use it for any other device laptop, or desktop in your network. Also as it is private IP, it is not accessible from outside the local network.

Changing 10.10 0.1 To Other IP Address

This is IP address is hardcoded in a router or modem firmware and as such, you can not change it to other IP addresses like 192.168.1.254, 192.168.100.1

Resetting the password for 10.10 0.1 IP:

  • Suppose that you have forgotten your password for the login credentials to this router. Most of the router reset buttons are at the back of the router. Sometimes, this can also be found out from the side panel of the router box itself.
  • Just press and hold on to the button for an approximate time of about 10 to 20 seconds and then the modem will automatically get reset to the default factory settings. But please note that once you reset your modem, you will initially lose the internet connectivity online.
  • Suppose you do not have much of the required knowledge and expertise in this area, it is therefore highly recommended that you take help and advice from an expert or any industrial person.

Leave a Reply

Your email address will not be published.